g 6 CPUs, 4 hotplug CPUs
nr_irqs_gsi: 24
Allocating PCI resources starting at d0000000 (gap: d0000000:2ff00000)
NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:6 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @c3400000 s29848 r0 d23400 u524288
pcpu-alloc: s29848 r0 d23400 u524288 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3 4 5 - - 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 845103
Kernel command line: root=/dev/ram0 ro init=/linuxrc ramdisk=8192 real_root=/dev/hda5
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:000cff90)
Memory: 3370732k/3407424k available (4316k kernel code, 35020k reserved, 1662k data, 356k init, 2498120k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff1f000 - 0xfffff000   ( 896 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc15d7000 - 0xc1630000   ( 356 kB)
      .data : 0xc1437266 - 0xc15d6c74   (1662 kB)
      .text : 0xc1000000 - 0xc1437266   (4316 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
NR_IRQS:512
CPU 0 irqstacks, hard=c3400000 soft=c3401000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 4 timers in total, 1 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 2812.790 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5625.58 BogoMIPS (lpj=11251160)
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
using C1E aware idle routine
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) II X2 240e Processor stepping 02
CPU 1 irqstacks, hard=c3480000 soft=c3481000
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5625.31 BogoMIPS (lpj=11250629)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: AMD Athlon(tm) II X2 240e Processor stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
System has AMD C1E enabled
Switch to broadcast mode on CPU1
Total of 2 processors activated (11250.89 BogoMIPS).
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
Switch to broadcast mode on CPU0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
PCI: Using configuration type 1 for base access
PCI: Using configuration type 1 for extended access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI Error (psargs-0359): [ECEN] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\] (Node c1665af8), AE_NOT_FOUND
ACPI: Executed 4 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
ACPI Warning: Incorrect checksum in table [OEMB] - 43, should be 3E (20090903/tbutils-314)
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:11.0: reg 10 io port: [0xb000-0xb007]
pci 0000:00:11.0: reg 14 io port: [0xa000-0xa003]
pci 0000:00:11.0: reg 18 io port: [0x9000-0x9007]
pci 0000:00:11.0: reg 1c io port: [0x8000-0x8003]
pci 0000:00:11.0: reg 20 io port: [0x7000-0x700f]
pci 0000:00:11.0: reg 24 32bit mmio: [0xfe7ffc00-0xfe7fffff]
pci 0000:00:11.0: set SATA to AHCI mode
pci 0000:00:12.0: reg 10 32bit mmio: [0xfe7fe000-0xfe7fefff]
pci 0000:00:12.1: reg 10 32bit mmio: [0xfe7fd000-0xfe7fdfff]
pci 0000:00:12.2: reg 10 32bit mmio: [0xfe7ff800-0xfe7ff8ff]
pci 0000:00:12.2: supports D1 D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:12.2: PME# disabled
pci 0000:00:13.0: reg 10 32bit mmio: [0xfe7fc000-0xfe7fcfff]
pci 0000:00:13.1: reg 10 32bit mmio: [0xfe7fb000-0xfe7fbfff]
pci 0000:00:13.2: reg 10 32bit mmio: [0xfe7ff400-0xfe7ff4ff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
pci 0000:00:14.1: reg 20 io port: [0xff00-0xff0f]
pci 0000:00:14.2: reg 10 64bit mmio: [0xfe7f4000-0xfe7f7fff]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
pci 0000:00:14.5: reg 10 32bit mmio: [0xfe7fa000-0xfe7fafff]
pci 0000:01:05.0: reg 10 32bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:01:05.0: reg 14 io port: [0xc000-0xc0ff]
pci 0000:01:05.0: reg 18 32bit mmio: [0xfe9f0000-0xfe9fffff]
pci 0000:01:05.0: reg 24 32bit mmio: [0xfe800000-0xfe8fffff]
pci 0000:01:05.0: supports D1 D2
pci 0000:00:01.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfe800000-0xfe9fffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:00.0: reg 10 io port: [0xd800-0xd8ff]
pci 0000:02:00.0: reg 18 64bit mmio pref: [0xfdeff000-0xfdefffff]
pci 0000:02:00.0: reg 20 64bit mmio pref: [0xfdef8000-0xfdefbfff]
pci 0000:02:00.0: reg 30 32bit mmio pref: [0xfeae0000-0xfeafffff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:05.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:05.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci 0000:00:05.0: bridge 64bit mmio pref: [0xfde00000-0xfdefffff]
pci 0000:03:00.0: reg 10 64bit mmio: [0xfebff800-0xfebfffff]
pci 0000:03:00.0: reg 18 io port: [0xe800-0xe8ff]
pci 0000:03:00.0: supports D2
pci 0000:03:00.0: PME# supported from D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:06.0: bridge io port: [0xe000-0xefff]
pci 0000:00:06.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
pci 0000:04:06.0: reg 10 32bit mmio pref: [0xfdfff000-0xfdffffff]
pci 0000:04:06.1: reg 10 32bit mmio pref: [0xfdffe000-0xfdffefff]
pci 0000:00:14.4: transparent bridge
pci 0000:00:14.4: bridge 32bit mmio pref: [0xfdf00000-0xfdffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 12 14 15) *0, disabled.
vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 0
hpet0: 4 comparators, 32-bit 14.318180 MHz counter
hpet: hpet2 irq 24 for MSI
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0x40b-0x40b has been reserved
system 00:0a: ioport range 0x4d6-0x4d6 has been reserved
system 00:0a: ioport range 0xc00-0xc01 has been reserved
system 00:0a: ioport range 0xc14-0xc14 has been reserved
system 00:0a: ioport range 0xc50-0xc51 has been reserved
system 00:0a: ioport range 0xc52-0xc52 has been reserved
system 00:0a: ioport range 0xc6c-0xc6c has been reserved
system 00:0a: ioport range 0xc6f-0xc6f has been reserved
system 00:0a: ioport range 0xcd0-0xcd1 has been reserved
system 00:0a: ioport range 0xcd2-0xcd3 has been reserved
system 00:0a: ioport range 0xcd4-0xcd5 has been reserved
system 00:0a: ioport range 0xcd6-0xcd7 has been reserved
system 00:0a: ioport range 0xcd8-0xcdf has been reserved
system 00:0a: ioport range 0x800-0x89f has been reserved
system 00:0a: ioport range 0xb00-0xb0f has been reserved
system 00:0a: ioport range 0xb20-0xb3f has been reserved
system 00:0a: ioport range 0x900-0x90f has been reserved
system 00:0a: ioport range 0x910-0x91f has been reserved
system 00:0a: ioport range 0xfe00-0xfefe has been reserved
system 00:0a: iomem range 0xffb80000-0xffbfffff has been reserved
system 00:0a: iomem range 0xfec10000-0xfec1001f has been reserved
system 00:0b: ioport range 0xe80-0xf5f has been reserved
system 00:0b: ioport range 0xae0-0xaef has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0xcfffffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0xc000-0xcfff
pci 0000:00:01.0:   MEM window: 0xfe800000-0xfe9fffff
pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:05.0: PCI bridge, secondary bus 0000:02
pci 0000:00:05.0:   IO window: 0xd000-0xdfff
pci 0000:00:05.0:   MEM window: 0xfea00000-0xfeafffff
pci 0000:00:05.0:   PREFETCH window: 0x000000fde00000-0x000000fdefffff
pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
pci 0000:00:06.0:   IO window: 0xe000-0xefff
pci 0000:00:06.0:   MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:14.4: PCI bridge, secondary bus 0000:04
pci 0000:00:14.4:   IO window: disabled
pci 0000:00:14.4:   MEM window: disabled
pci 0000:00:14.4:   PREFETCH window: 0xfdf00000-0xfdffffff
pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:06.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xc000-0xcfff]
pci_bus 0000:01: resource 1 mem: [0xfe800000-0xfe9fffff]
pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:02: resource 0 io:  [0xd000-0xdfff]
pci_bus 0000:02: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:02: resource 2 pref mem [0xfde00000-0xfdefffff]
pci_bus 0000:03: resource 0 io:  [0xe000-0xefff]
pci_bus 0000:03: resource 1 mem: [0xfeb00000-0xfebfffff]
pci_bus 0000:04: resource 2 pref mem [0xfdf00000-0xfdffffff]
pci_bus 0000:04: resource 3 io:  [0x00-0xffff]
pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:01:05.0: Boot video device
Unpacking initramfs...
Freeing initrd memory: 568k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
microcode: CPU0: patch_level=0x1000098
microcode: CPU1: patch_level=0x1000098
Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
highmem bounce pool size: 64 pages
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/O].
fuse init (API version 7.13)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 1707
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler cfq registered (default)
pcieport 0000:00:05.0: irq 25 for MSI/MSI-X
pcieport 0000:00:05.0: setting latency timer to 64
pcieport 0000:00:06.0: irq 26 for MSI/MSI-X
pcieport 0000:00:06.0: setting latency timer to 64
Real Time Clock Driver v1.12b
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: processor limited to max C-state 1
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D0._STA] (Node f7039810), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\PRID.P_D1._STA] (Node f7039784), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D0._STA] (Node f7039edc), AE_NOT_EXIST
ACPI Error: No handler for Region [SACS] (f70403e4) [PCI_Config] (20090903/evregion-319)
ACPI Error: Region PCI_Config(2) has no handler (20090903/exfldio-295)
ACPI Error (psparse-0537): Method parse/execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
ACPI Error (uteval-0250): Method execution failed [\SECD.S_D1._STA] (Node f7039e50), AE_NOT_EXIST
loop: module loaded
Uniform Multi-Platform E-IDE driver
atiixp 0000:00:14.1: IDE controller (0x1002:0x439c rev 0x00)
pci 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
atiixp 0000:00:14.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xff00-0xff07
    ide1: BM-DMA at 0xff08-0xff0f
Probing IDE interface ide0...
hda: SAMSUNG SP1604N, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
ide-cd driver 5.00
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 27 for MSI/MSI-X
eth0: RTL8168d/8111d at 0xf8036000, 40:61:86:5c:d6:20, XID 081000c0 IRQ 27
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe7ff800
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32-gentoo-r1 ehci_hcd
usb usb1: SerialNumber: 0000:00:12.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe7ff400
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32-gentoo-r1 ehci_hcd
usb usb2: SerialNumber: 0000:00:13.2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe7fe000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32-gentoo-r1 ohci_hcd
usb usb3: SerialNumber: 0000:00:12.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe7fd000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.32-gentoo-r1 ohci_hcd
usb usb4: SerialNumber: 0000:00:12.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe7fc000
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32-gentoo-r1 ohci_hcd
usb usb5: SerialNumber: 0000:00:13.0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe7fb000
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.32-gentoo-r1 ohci_hcd
usb usb6: SerialNumber: 0000:00:13.1
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 3 ports detected
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe7fa000
usb 1-5: new high speed USB device using ehci_hcd and address 2
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: OHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.32-gentoo-r1 ohci_hcd
usb usb7: SerialNumber: 0000:00:14.5
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Linux video capture interface: v2.00
bttv: driver version 0.9.18 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv 0000:04:06.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
bttv0: Bt878 (rev 17) at 0000:04:06.0, irq: 21, latency: 64, mmio: 0xfdfff000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
IRQ 21/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 0-0050: Hauppauge model 44354, rev C242, serial# 3902432
tveeprom 0-0050: tuner model is Temic 4009FR5 (idx 42, type 20)
tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 0-0050: audio processor is MSP3415 (idx 6)
tveeprom 0-0050: has radio
bttv0: Hauppauge eeprom indicates model#44354
bttv0: tuner type=20
msp3400 0-0040: MSP3415G-B8 found @ 0x80 (bt878 #0 [sw])
msp3400 0-0040: msp3400 supports nicam and radio, mode is autodetect and autoselect
tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner-simple 0-0061: creating new instance
tuner-simple 0-0061: type set to 20 (Temic PAL_BG (4009 FR5) or PAL_I (4069 FR5))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
input: i2c IR (Hauppauge) as /devices/virtual/input/input2
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [bt878 #0 [sw]]
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
Bt87x 0000:04:06.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
bt87x0: Using board 1, analog, digital (rate 32000 Hz)
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
usb 1-5: New USB device found, idVendor=03f0, idProduct=1424
usb 1-5: New USB device strings: Mfr=10, Product=11, SerialNumber=0
usb 1-5: Product: f2105 2PORT USB 2.0 HUB
usb 1-5: Manufacturer: HPÿ
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 2 ports detected
hda_codec: ALC889: BIOS auto-probing.
ALSA device list:
  #0: HDA ATI SB at 0xfe7f4000 irq 16
  #1: Brooktree Bt878 at 0xfdffe000, irq 21
TCP cubic registered
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) II X2 240e Processor processors (2 cpu cores) (version 2.20.00)
powernow-k8:    0 : pstate 0 (2800 MHz)
powernow-k8:    1 : pstate 1 (2100 MHz)
powernow-k8:    2 : pstate 2 (1600 MHz)
powernow-k8:    3 : pstate 3 (800 MHz)
Using IPI No-Shortcut mode
Freeing unused kernel memory: 356k freed
usb 4-3: new full speed USB device using ohci_hcd and address 2
usb 4-3: New USB device found, idVendor=046a, idProduct=0052
usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-3: Product: Wireless Keyboard and Mouse
usb 4-3: Manufacturer: Cherry
usb 4-3: configuration #1 chosen from 1 choice
input: Cherry Wireless Keyboard and Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-3/4-3:1.0/input/input3
generic-usb 0003:046A:0052.0001: input: USB HID v1.10 Keyboard [Cherry Wireless Keyboard and Mouse] on usb-0000:00:12.1-3/input0
input: Cherry Wireless Keyboard and Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-3/4-3:1.1/input/input4
generic-usb 0003:046A:0052.0002: input: USB HID v1.10 Mouse [Cherry Wireless Keyboard and Mouse] on usb-0000:00:12.1-3/input1
usb 1-5.2: new low speed USB device using ehci_hcd and address 4
usb 1-5.2: New USB device found, idVendor=0bc7, idProduct=0006
usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-5.2: Product: RF receiver
usb 1-5.2: Manufacturer: X10 WTI
usb 1-5.2: configuration #1 chosen from 1 choice
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
lirc_dev: IR Remote Control driver registered, major 61 

lirc_atiusb: USB remote driver for LIRC $Revision: 1.85 $
lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
lirc_dev: lirc_register_driver: sample_rate: 0
lirc_atiusb[4]: X10 WTI RF receiver on usb1:4
usbcore: registered new interface driver lirc_atiusb
Linux agpgart interface v0.103
EXT3 FS on hda5, internal journal
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to userspace modesetting.
pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:01:05.0: setting latency timer to 64
[drm] Initialized radeon 1.31.0 20080528 for 0000:01:05.0 on minor 0
Adding 4192924k swap on /dev/hda1.  Priority:-1 extents:1 across:4192924k 
r8169: eth0: link up
r8169: eth0: link up
[drm] Setting GART location based on new memory map
[drm] Loading RS780 CP Microcode
platform r600_cp.0: firmware: requesting radeon/RS780_pfp.bin
platform r600_cp.0: firmware: requesting radeon/RS780_me.bin
[drm] Resetting GPU
[drm] writeback test succeeded in 1 usecs
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
[drm] Resetting GPU